Maple Wood Edge Banding Tape 2'' 25' Roll
from Band-It
- Heat-sensitive adhesive backing (iron on)
- Real wood
- 2''
- 25' long
Edge Tape is for covering the edges of plywood and other non-wood edges and surfaces that need to be nicely finished. Common uses are for furniture and cabinetry, but edge tape will adhere to nearly any type of surface. All edge tape has a heat-sensitive glue backing and applies quickly with an iron.
5PK Edge Trimmer Blade
from CLOVERDALE CO INC
- 5 PK EDGE TRIMMER BLADES
- KW's: wood trim veneer trimmer edge
Band-It, 5 Pack, Replacement Blades For Band-It Edge Trimmer.
FastCap Adhesive Cover Caps PVC White 9/16" (1 Sheet 52 Caps)
from FastCap
- Cover screws with these easy to apply matching adhesive caps.
- 9/16" dia Adhesive Cover Cap
- PVC Adhesive Cap
- To see all cover caps, Search: FastCap Adhesive Cover Caps
PVC Adhesive Cap (52 ea per sheet)
Band-It Edge Trimmer
from CLOVERDALE CO INC
- Trims edges clean and flush
- Cuts in both directions
- Uses inexpensive, easy-to-replace blades
- Safe
Band-It Edge Trimmer, Single-Sided, Compact & Durable, Trims In Both Directions.
Cloverdale 24910 Band-It Wood Veneer Facing
from Cloverdale
- 24X96 RED OAK VENEER
- KW's: wood veneer trim
Made of hardwoods, veneer is presanded and ready for finishing. Use for redoing antiques, kitchen cabinets, tables, or putting the finishing touches on hobby projects. Veneer is backed with resin impregnated thermoset paper for easy handling and added str
24'' x 24'' Pressure Sensitive Veneer - Walnut (Plain Sliced)
from Rockler
- Premium grade 1/64'' thick flexible veneer.
Apply without mess or expensive tools! Unfinished real wood. Accepts stains and finishes. Straight grained. Grain runs the length of the roll.
This premium grade 1/64" thick flexible veneer comes with a 10 mil thick paper for stability and a pressure sensitive adhesive applied to its backside. Simply cut the veneer to size with a scissors, peel off the backing, and apply to the substrate. You can strengthen the bond between the veneer and substrate by applying pressure with a veneer smoothing blade. Pressure sensitive veneer permanently bonds to wood, glass, plastic and metal. Not recommended for use on fir plywood. It also accepts stains and finishes.
White Melamine Edge Banding Tape 7/8'' 25' Roll
from Band-It
- Heat-sensitive adhesive backing (iron on)
- Real wood
- 7/8'' wide
- 25' long
Edge Tape is for covering the edges of plywood and other non-wood edges and surfaces that need to be nicely finished. Common uses are for furniture and cabinetry, but edge tape will adhere to nearly any type of surface. All edge tape has a heat-sensitive glue backing and applies quickly with an iron.
13/16 X25 ft Iron on Edge White
from Rockler
Two ply polyester Edgemate edge-banding with a hot melt adhesive backing. If you can iron, you can apply Edgemate!
Walnut Wood Edge Banding Tape 7/8'' 25' Roll
from Band-It
- Heat-sensitive adhesive backing (iron on)
- Real wood
- 7/8'' wide
- 25' long
Edge Tape is for covering the edges of plywood and other non-wood edges and surfaces that need to be nicely finished. Common uses are for furniture and cabinetry, but edge tape will adhere to nearly any type of surface. All edge tape has a heat-sensitive glue backing and applies quickly with an iron.
Birch - 48'' x 10'' Dimensional Veneers- No Backing
from Rockler
Save time and money! 48" long veneer. When you buy this veneer, there is no waste because it has straight, parallel edges and no defects. Unfinished real wood with no paper backing. Accepts stains and finishes. Grains run lengthwise. Approximate sizes usually run about 1/2" over. All dimensional veneers are plain sliced unless otherwise noted.
NOTE: Because of special handling requirements, there is a two sheet minimum order for this product.
+++
Fastcap STAPE.6.5x50 6.5-Inch x 50-Foot Double Face Speedtape Glue
The Fastcap STAPE.6.5x50 is a 50-Foot Roll of 6.5-Inch Preglued Double Face Speedtape. SpeedTape is FastCap's high quality adhesive in a peel and stick roll!. Apply SpeedTape to your veneers and laminates, peel off the liner and stick it! If you have a peel and stick application, SpeedTape is the answer you are looking for!
Fastcap STAPE.1.5x50 1-1/2 Inch x 50-Foot Double Face Speedtape Glued
The Fastcap STAPE.1.5x50 is a 50-Foot roll of 1-1/2 Inch Preglued Double Face Speedtape. SpeedTape is FastCap's high quality adhesive in a peel and stick roll! Apply SpeedTape to your veneers and laminates, peel off the liner and stick it! If you have a peel and stick application, SpeedTape is the answer you are looking for!
Porter-Cable 43730PC Two-Flute Laminate Flush Trimming Router Bit
The Porter-Cable 43730PC is a 2 Flute Laminate Flush Trimming Router Bit. The bit is annealed and heat treated to Rockwell hardness of 40-45, harder than is possible with cast steel bodies. The bit is precisely ground using computer controlled machining for precision tolerances and perfectly concentric shafts. The carbide tip is made from a specially blended micro grain carbide for superior results and longer lasting sharpness. The ball-bearing pilot on this bit guides the cutter for flush trimming laminates and veneers.
Porter-Cable 43290PC 1/2 inches Laminate Flush Trim Router Bit
Porter-Cable Professional Edge router bit is constructed of 4140 Alloy Steel. It is a harder grade of steel than standard cast steel bit bodies. The carbide tip is made from specially blended micro grain carbide for superior results and longer lasting sharpness. The ball-bearing pilot on the bit guides the cutter for flush trimming laminates and veneers.
Festool 574288 MFK 700 EQ Trim Router Set
ToolKing.com promotional discount codes or coupons are NOT valid on Festool productsThe Festool 574288 is a MFK 700 EQ Trim Router Set. Due to its modular design, the MFK 700 is a cost-saving multipurpose: simply change the router base, rather than reaching for a different tool, and youll be equipped to handle any tasks involving edges and corners. Attach the appropriate base in a few simple steps - and youre ready to trim veneers or rout grooves straightaway. With its large support base and additional hand grip, the MFK 700 can be optimally and safely controlled - without tilting, even when routing around corners. The parallel side fence with fine adjustment (1/256-Inch or 1/10mm increments) delivers perfect corners. The dust extraction system - positioned directly on the base - removes chips and dust without getting in your way. The router base is inclined 1.5 to facilitate safe routing of laminated boards or edge banding requiring no additional finish work. The 90 base cut-out facilitates quick flush trimming of gluedon veneer - even around corners. The V-shaped cut-out of the base and sensor bearing guide provide quick flush trimming even around corners. The MFK 700 with its 720 Watt motor will quickly become the most versatile tool in your shop
